Friday, September 23, 2011

How do you change a defective brake light on a 99 honda odyssey?

bring your car to the nearest honda mechanic center

The driver's side brake light doesn't work?

I have a 1968 mustang.

the emergency light, signal light, and driving lights are working fine except for the driver's side brake light.

I've tried to change the light bulb but it still doesn't work.

How can I fix this problem?
The driver's side brake light doesn't work?
Perhaps the fuse? Im not 100% sure if it could be the fuse as it is only one light that's out. If not than i reckon it may be the resistor.

Good Luck!
The driver's side brake light doesn't work?
That's really weird, because it shares the same circuit as the flashers and turns, I'd almost be willing to bet it's an under dash problem, from switch to circuit, how you fix it I'm not sure, I have a bunch of nifty diagnostic tools to find the problem myself.
The odd part is, that can really only be a light bulb issue. my suggestion to you is to get a multimeter, and check for power at the bulb assembly (you should get around 12V DC power) and if you get power,(make sure someone has your brakes depressed) then it is a faulty ground with your bulb assembly. Clean out the insides really well or replace if possible. If you dont get power at the assembly, then you are unfortunatly going to have to chase the wire using the multimeter to find the point where there is a possible open in your lines. Im not sure of Ford wiring color schemes, but the running lights, brake lights, and turn lights should all be a different color. Good luck!
check the contact with a volt meter, if getting juice when you step on the brake then wiring is OK, but may not be getting contact to bulb, also check ground for this bulb contact, if no juice when you step on brake.
You have a 42 yr old wiring harness Its time to replace it. My Bronco had allot of electrical gremlins until I replace the harness.

Brake job and a week later the brake warning light goes out. Why?

Hi, I changed the front brake pads, rotors, sensor and flushed four liters of brake fluid on a friends 2001 740i and the brake light was still on. I told him the brakes are safe and I will figure out the light later. A week later he said the light must have Reset. Did it? What is up with that? I didn't have that happen with my 92 525iT.
Brake job and a week later the brake warning light goes out. Why?
The proportioning valve recentered itself after a few brake cycles.
Brake job and a week later the brake warning light goes out. Why?
Duty Cycles.



Some codes will reset after a number of cycles without the code coming back up. Cycles being times started, hours run, etc.
the float sensor may have got stuck in the down position that made the light come one and he may have hit a bump and it unstuck itself.....
i really don't know. if i were to guess i would say that the parking brake was partially on and when it was applied and later released the light would go out. sorry.
Yes it can happen. ABS systems have proportioning valves in them. If they are out of %26quot;balance%26quot; the brake warning light comes on. Usually a brake job and or bleeding will 'reset%26quot; them and the light will go off. One may have been hung up or the brakes were not bled completely. Even though you pulled that much fluid through there still may have been some air somewhere.
Vehicles are equipped with a brake proportioning valve, meaning what ever pressure is greater it will push a piston to block the other port. In the event of a rupture in the system, the valve is a safety feature allowing full pressure to be applied either to the front or rear axle, even though there is a break in the system.

A small amount of air was likely trapped in the line. Air will eventually find it's way to the highest point meaning the master cylinder. Once the air has vacated the system the valve recenters itself %26amp; the light will go out.



禄禄禄
Man! Are the brakes still working good to bring the auto to a good safe stop every time? The warning light went out on it's own after staying on after the repair job? What IS a 740i? Do you know what it is on that particular auto that activates the brake warning light? For all of the work you stated you did on repairing what you determined to be %26quot;bad%26quot; with the brakes it would seem that you covered everything. The sensor that you listed as having been changed. Was it designed to indicate a low lever of brake fluid in the hydraulic cylinder supply reservoir? Are you sure that you could NOT have allowed an air bubble to remain in the entire hydraulic fluid piping system somewhere nearby that sensor?

If the brake warning light %26quot;reset itself%26quot;, has stayed %26quot;reset%26quot; and the brakes are working perfectly anyway, it MIGHT be that the bulb just flat worked too long and burned out. Oh, NO! I want to believe that whatever caused that light to stay on again after you did all that work, %26quot;got fixed%26quot; on its own, and everything is O.K.! Tell your friend just to be very conscious every time he applies the brakes on his car that HE feels confident that they're working JUST FINE!%26lt;G%26gt;
Yeah, most likely the codes for any repairs you've resolved need a reset. There is a speail device used or you can try disconnect the battery because if you ever need a battery, you will. Hopefully, you retained the owner's manual which should continue to be with the car...for radio code, alarm, etc.
  • How to make a fleece T-shirt quilt
  • columnheader
  • How do you change the third brake light on a 98 civic hatchback?

    you should just be able to get at it from the inside or you might have to remive a cover on the inside held on by a couple of screws then pop the old bulb out and replace with a new bulb of the same kind....

    How do i change the top brake light on a 1997 BMW 540i?

    It looks like something needs to slide but its not moving. Any help???
    How do i change the top brake light on a 1997 BMW 540i?
    The best answer is in your owner's manual. If not try getting the proper chilton's manual. It will tell how to do it step by step, with pictures and what tools you need. Chilton's have helped me many times.
    How do i change the top brake light on a 1997 BMW 540i?
    open trunk look socket twist on it and pull and your done. new one bulb use clean rag not your finger

    to put back

    How do i change a brake light switch on a ford galaxy ?

    lie upside down under the steering wheel,unclip the plug and turn the switch 1/4 of a turn and its out...when refitting make sure the switch is pushed in flat and turn....check it works correctly
    How do i change a brake light switch on a ford galaxy ?
    brake light switch is just above the brake pedal remove nut and a wire .. only hard part is laying upside down in the seat....sure its not a light bulb which burns out a lot more than any brake light switch been driving over 40 yrs and working on cars about has long only replace one
    How do i change a brake light switch on a ford galaxy ?
    Under the dash, touching the brake pedal will be push button type swithch, remove and replace with new one.
    You don't mention what year Galaxie. The old style were mounted on the master cylinder. The newer %26quot;old style%26quot; are attached to a support above the brake pedal. Either are simple to remove and replace.

    How do i change the brake light in a 1997 camry?

    pull the trunk liner back. twist the bulb housing and pull it out. take out the old bulb and put a new one in. reverse the process.simple : )
    How do i change the brake light in a 1997 camry?
    open the trunk and pull back the carpet where the light would be. there should be a twist off peice. twist it and viola. change the light and done.

    ES330 Lexus 2004 how do I change light bulb on the 3rd brake light ( in rear window)?

    open the trunk and look up from under neath the deck lid.if not there you need to remove the push pins on each side of the cover,remove the cover then replace the bulbs,
    ES330 Lexus 2004 how do I change light bulb on the 3rd brake light ( in rear window)?
    take it apart
  • acne on back shoulders
  • heal yellowing toenails
  • I changed my brake line on my 01 ram ,bleed both rear brakes.abs light and brake light still on?

    It was the 7` line that comes from the junction box behind drivers front wheel and runs to rear brake same side.I bleed both rears.should or do i need to bleed fronts as well? I drove truck and it stops good.
    I changed my brake line on my 01 ram ,bleed both rear brakes.abs light and brake light still on?
    check fluid and bleed all the wheels



    once air enters system have to bleed it all just smarter
    I changed my brake line on my 01 ram ,bleed both rear brakes.abs light and brake light still on?
    There is also a bleed valve on the ABS valve. You have to bleed that also. Then if the light is still on, try disconnecting the battery. This should re-set the computer.
    if you just replaced the rear line then you don,t have to bleed the front too, i never did ! check the plug-in on the wheel sensors. maybe you bumped 1 of them or it,s corroded.
    None of that has anything to do with the ABS light. They're almost always on because a wheel sensor isn't reading right.

    What specifically does the red BRAKE warning light mean in a 2002 VW Cabrio?

    I don't have a manual for my 2002 VW Cabrio. The brake warning light just came on - The word BRAKE in red capital letters. Is this a brake fluid problem, a sensor problem, etc.? The parking brake isn't on, and it drives and brakes fine. Just had my brake pads changed in March of '08, so that shouldn't be the problem.
    What specifically does the red BRAKE warning light mean in a 2002 VW Cabrio?
    Brake warning lights come on when you are low on fluid. Also, in some vehicle them come on for a few seconds when the vehicle is started. It could also be a sensor problem. I would take it to a shop, and they will be able to plug into the computer and read what the computer says is wrong.
    What specifically does the red BRAKE warning light mean in a 2002 VW Cabrio?
    Could be 2 problems, parking brake engaged or low fluid in the master cylinder.
    it could be any of the above, low fluid level,a pressure difference in the two halves of the system, a brake lamp that is out, an e brake that is still partially on, or pads that have worn to a minimum. my best advice is that you get the brakes checked out by a professional.

    How do i change the right brake light in my 93 cavalier?

    Open the trunk, peel back the carpet trim to get at the back of the light. Follow the wires to the appropriate bulb. See the other side for the brake bulb location. Usually the bulb housing twists or clips out of socket, replace bulb and reinstall.
    How do i change the right brake light in my 93 cavalier?
    Open the trunk and look for the wingnuts that hold on the light assembly. The are usually black plastic wingnuts in the back corners of the inside of the trunk. Pull back the black material that lines the inside of the truck and then wiggle the whole light assembly out of place from outside the vehicle. This should give you access to the bulbs. Turn out the electrical connector and the bulb should be right there.
    How do i change the right brake light in my 93 cavalier?
    remove the battery and air filter, add brake fluid, then disconnect the steering wheel.
    Look in the trunk and look for a access panal or something like that and open it.There might be nothing to take off to get to the bulb. Locate the burned out bulb and carefully remove the socket from it's carryer and remove the bulb.Take it to a part's store and get the replacement bulb,just reverse the removal procedure.Then turn your headlight's on and your hazard light's to check if it's all working right...

    How do you change the brake light on a 1998 chevy malibu?

    You can download a PDF copy of your Owners Manual which should cover it here;

    https://www.mygmlink.com/main/US/en/gm/h鈥?/a>
    How do you change the brake light on a 1998 chevy malibu?
    Inside the trunk there should be some wing nuts to unscrew, releasing the cover.

    How do i change the brake light in a 2000 Ford Mustang?

    open the trunk, and pull away carpet right behind taillights (will be held down with fir tree fasteners) to access sockets, sockets twist about a quarter turn or so to release. The third brake light is also replaceable with the trunk open, look up and you'll see
  • database
  • Where i can buy server to host my own web site
  • Brake light on 1983 dodge power ram 150?

    I have a red brake light on i just had my rear brakes changed but the light is still on what makes that light go on? i cant seem to find anything around the drum or brake shoes wear would the sensor be or what would set it off how can i fix this?
    Brake light on 1983 dodge power ram 150?
    sensor is usually on the master cylinder and is telling you you have low fluid check that
    Brake light on 1983 dodge power ram 150?
    An '83 Ram PU isn't going to have a low fluid level warning light. That's just the normal brake warning light, which is triggered by a sensor in your proportioning valve (a little metal block that the 2 lines from the master go into, and then 3-4 lines come out to the wheels, just below the master). It shows that there is some sort of an imbalance in pressure between the 2 brake circuits. A lot of times it will be on after a brake job because the wheel cylinders got pushed back in to make room for the new shoes. It will usually go out after you press the brake pedal a few times. If not, it could be that the proportioning valve needs to be reset, or the wheel cylinders started leaking when they were pushed in. Normally, it will come on if you have a fluid leak, air in the lines, or a bad master cylinder plunger.

    Can anyone tell me how to change a brake light on a 1999 ford focus?

    take out the old one and put in the new one
    Can anyone tell me how to change a brake light on a 1999 ford focus?
    meow
    Can anyone tell me how to change a brake light on a 1999 ford focus?
    Open the boot and remove the casing, take out the old bulb and put in the new one, return the casing, close the boot and away you go! Oh, you might wanna test that it works first - to do this you need to get someone to turn on the ignition and put their foot on the brake while you check to see if it works! Good luck
    You should have a book that came with the car that will tell you all the details. What globe to buy, how to undo the light fixture and remove the old globe and then reverse the process. Other than that I am sure the Ford website for your region would have a handbook online.

    On my 2003 Ford Falcon (yes they still make the Falcon in Australia) you unscrew the light fitting using a phillips head screwdriver and pull the fitting away from the body of the car. The wires stay attached so don't pull too hard. You then unscrew the brake light fitting by turning a 1/4 turn or so to release, then do the same with the globe. In Australia these are both anti-clockwise. Then just reverse the order with the new globe.
    Some you have an access panel inside the car, others are as simple as taking off the tail light. I don't know which you have, sorry.
    HANDBOOK?

    How to change brake light on 2003 cts?

    To replace the tail, stop, turn signal or side-marker lamps use the following procedure:

    1. Open the trunk using the trunk button on the remote keyless entry transmitter or the trunk release button located on the lower part of the driver鈥檚 door.

    2. Remove the compact spare tire cover by turning the wing nut counterclockwise.

    3. Remove the four convenience net wing nuts.

    4. Pull the carpet back away from the body of the vehicle on the side with the burned out bulb.

    5. Remove the two mounting screws from the lamp assembly.

    6. Pull out the lamp assembly to expose the bulb sockets.

    7. Turn the bulb socket one-quarter turn counterclockwise and pull the bulb and socket out of the lamp reflector.

    8. Pull the old bulb from the bulb socket keeping the bulb straight as you pull it out.

    9. Install a new bulb.

    10. Reverse the steps to reinstall the lamp assembly.

    How do you change the brake light switch in a dodge stratus 2003?

    Disconnect the link clip and pull it out, disconnect the wiring. Reverse procedure to install.

    Car Brake Light not working, even after I changed out the bulb?

    My left side brake light is not working. I changed out the light bulb a few times but still not working. It can't be the fuse because the right side is working. How do I find out why the left side ain't working? Where and what do I look for in the wiring? Please help
    Car Brake Light not working, even after I changed out the bulb?
    take it to an auto parts store most of the time they will tell you what the problem is and where and how to fix it without charging you
    Car Brake Light not working, even after I changed out the bulb?
    check the wiring it might be hosed up
    Look to see if there is corrosion in the bulb socket,if there is clean it with small brush and qtip with alcohol.

    Then put some bulb grease into the socket to help from having this problem again.
    first you should clean the contacts in the left side brake light and check it with a tester or a meter to see if you're getting powere to it. just turn on the left signial light and you should get an interminting power indication if its working. if this does not help then you need to check for loose wiring on the left side for the brake lights.. you can check the lights to determine the color of wird you gonna be checking for loose or broken .
    first thing is to check power for both terminal in the light bulb holder, if you have power to both, then check for a ground that is loose in the trunk of the vehicule on the side that is out. if the terminals looks grey in colour, try and clean the contact area, the correct colour is copper
    it actually could be the fuse. on some cars the left and right side have different fuses...if you have the owners manueal it usually has a troubleshooting guide for little things like that if it not the fuse or the wiring it could be needing some work....but i dont think itll be that
    Some of the other answers look good, especially the checking for power on the contacts of the socket. Also, IF your turn signal and brake light use the same bulb try turning on your emergency blinkers and see if it blinks. If not, the socket may be corroded, a fuse could be blown and/or a wire broken.



    One other thought. IF the brake light and turn signal use the same bulb, it could be a defective turn signal selector switch since that switch turns off the brake light when you choose LEFT turn. If the turn signal selector switch didn't do this the light would never blink in the turn signal mode. Good luck. Pops
    Knowing make and model would be helpfull the year would be plus.

    not knowing that,some cars do have fuses for one side only,most american cars your assumption would be correct.

    most likely you are expieriencing a ground problem with your bulb socket try getting someone to apply the brake while you move the bulb side to side or twist the wiring into the socket some see if that makes it worl briefly.if it does your socket may be bad.hard to say .some cars have a fiber board that the bulb fits into and sometimes like on chey truck or volvos they melt inside requiring replacement
    what kind of car is it
    Check power to the socket with a test light. Put clamp end on a Good ground. Put on your lights on and test to see if you have a good ground on your test light but touching the probe to one of the contacts in the socket. One should light it up and the other will do nothing. Then turn the lights off and have someone step on the brake pedal.And check to see if one of the contacts makes the test light light up. If it does you just need to turn off all power and get a pick or paperclip with a little hook on it and pull up on those contacts a little so they make contact with the bulb correctly. If they don't light up at all and you know the test light is getting a good ground check the wiring in your trunk where it plugs into the light. A wire may have gotten damaged.

    They also sell replacement sockets if you find power at the plug but not in the socket. The replacement part can usually be purchased at Napa or auto zone. It's cheap and easy to install.
  • camping tent rental
  • have you ever been afraid to
  • How to take out a back brake light in the window for a 94 buick lesabre?

    the window brake light dont work i need to get to it out so i can change the light bulb
    How to take out a back brake light in the window for a 94 buick lesabre?
    2 screws on bott
    How to take out a back brake light in the window for a 94 buick lesabre?
    check ya trunk under neath should be screws and i think they leds you should replace whole thing junk yard usually got em and will check to make sure they work

    How do i change a brake light bulb on a 2004 chevy cavalier?

    you cant, just a new cluster, it is a sealed unit and they are illuminated by led
    How do i change a brake light bulb on a 2004 chevy cavalier?
    From inside the trunk pull back the carpet and you should see the tail lights. Twist and it should come right out.

    How can I turn off the brake light indicator & TCS light on 2003 Honda Accord?

    I just left the shop to have my brake fluid and oil changed. After leaving the shop I noticed the TCS light %26amp; brake light remained on. After 5 mins of driving the TCS light has gone off but the brake light remains on. What could be the problem?
    How can I turn off the brake light indicator %26amp; TCS light on 2003 Honda Accord?
    Just to tell you straight off, theres no way you can turn it off yourself (no buttons). Any car years 2000 and up are programed to leave those dash lights on until the car gets hooked up to a shop computer (diagnostic computer) and only them can really turn that off for you. The TCS is your Traction Control System which means that it turned on cuz the car had no traction (your wheels were spinning) and the TCS slows the tires down until the car got a grip on the road. The brake light might be cuz your brake shoes or rotors might be worn out but not too sure. My suggestion to you is to take the car back to the shop and ask them why this is happening only moments after you took your car out of the shop.

    I have a mazad b2300 an i am having a problem with the lights on the brakes. the abs light and the brake light

    the abs light and the brake light will not go out. i have change the brakes and that is not the problem. is there anyone that have any suggestion about what could be wrong with it.
    I have a mazad b2300 an i am having a problem with the lights on the brakes. the abs light and the brake light
    ABS sensor is bad. need to scan it to see which one

    Need to change a brake light on 2000 explorer, how do I get to it?

    You need to unscrew the tail light assembly then twist out the socket on the back.
    Need to change a brake light on 2000 explorer, how do I get to it?
    open the rear hatch and remove the screws to remove the taillight housing some later models are hidden behind the trim on the pillars or posts
  • how to flirt with your girlfriend
  • find my old friends
  • How do I change the centre (high) brake light on a Ford Fiesta Mk6 (2005)?

    The Ford manual specifies that you should %26quot;remove the 2 grommets%26quot; (on the inside top edge of the boot hatch), then release some kind of clip inside the now-exposed holes using a screwdriver. No matter how hard I try, I can't find ANYTHING to unscrew or unclip inside either of those holes!
    How do I change the centre (high) brake light on a Ford Fiesta Mk6 (2005)?
    Shine a light up into the holes to see how the release clip may work. Here's the general instructions (below). You may have to use force and know where to apply the force to snap the stoplight plastic housing off. Maybe the dealer would give you a clue knowing you bought your car there!



    %26quot;One place where you will run into the most problems is the Center Mount Stop Light (CMSL). Most are mounted inside the car on the rear deck lid. Removing these can be a problem. Some have mounting screws hidden by small plastic covers. Some have studs extending down into the trunk and are held in with small nuts. This requires you go into the trunk, remove the nuts and lift the whole assembly out. Some simply snap into place and can be difficult to remove if you don't know where the lock tabs are.%26quot;

    98 Taurus brake light swith,changed, but when I put the brown bushing back on, brake lights won't work. ?

    I put togerther without brown bushing and they work fine. Am I putting it on wronG? It won't fit any other way; push rod over peg coming out from pedal. Then brown busing pushed over brake pedal peg till it's inside the push rod. Then brake swith over both and secured with pin. Could the new switch not be sensitive enough with the busing in?
    98 Taurus brake light swith,changed, but when I put the brown bushing back on, brake lights won't work. ?
    maybe all it needs is adjusted.

    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?

    I think it might have something do with the signal lever seeing as it only seems to be the three lights operated by rotating the stick that dont work. Changing the fuse did not solve the problem... however the inside clock still works when the lighs are off but as soon as i rotate for the lights to come on the clock goes off!! and obviously no lights come on!



    Indicators and brake lights still work.



    Is this an electrical fault or is there something i have not thought to check yet?
    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?
    I had the exact problem. My signal lever was broken. I, too would recommend taking it in to the dealership, signal levers can be replaced, and if it happens to be a totally different problem, the car dudes can figure it out.

    Good luck!
    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?
    did you try putting the dimmer to the brightest position, if you turn on the light and the clock dissapears it might be dimmer that is very dim, try that, I couldn't understand the question very well, but try that , good luck!!!!!!
    check the tail lights.



    not sure if you call the indicators the tail lights, but that sounds like the next step in diagnosis, and its cheap
    And your car is a WHAT? We need year/make/model in order to give accurate answers.
    Your wiring is messed up!



    take it to the dealership
    just drive it in the day time

    How do I change the rear turn signal/brake light bulb in a 1998 Monte Carlo?

    I saw 2 thumb screws in trunk, took those off, but can't get brake lense off. Is this the right thing to do?
    How do I change the rear turn signal/brake light bulb in a 1998 Monte Carlo?
    There are three wing nuts that need to be removed to take the taillight out:

    1. Remove the visible plastic wing nut retaining the tail lamp.

    2. Pull back the corner of the rear compartment trim panel to access the remaining plastic wing nuts.

    3. Apply light pressure to the tail lamp lens to retain the lamp in position during removal of the remaining plastic wing nut retainers.

    4. Remove the remaining plastic wing nuts retaining the tail lamp.

    5. Carefully remove the tail lamp assembly from the rear body panel and support the tail lamp assembly.

    6. Rotate each lamp socket counterclockwise to release and remove from the tail lamp housing assembly.
    How do I change the rear turn signal/brake light bulb in a 1998 Monte Carlo?
    Keep going. I think there are either 3 or 4 of those wing nuts inside the trunk that hold the tail light onto the body. Take all off and the lamp will almost fall off. Then either remove the socket or take the screws out and get at the bulbs.
    either you twist the wiring outlet or remove screw so if one is looking at lense from outside and see no screw then try twisting the wiring inside

    My brake light is on all the time in my 1996 ford contour is it the e-brake and how do I change it?

    I need to get it inspected soon how do I change the e-brake cable or is their something I can do to make it pass inspection?
    My brake light is on all the time in my 1996 ford contour is it the e-brake and how do I change it?
    Is this the brake warning light on the dash? If so it is either the sensor on the parking brake, or a problem with the brakes in the vehicle. Is the master cylinder full of brake fluid? Do the brakes feel %26quot;squishy%26quot;?



    It could be that you have a leak in your brake system. It could be that your rear brakes are way out of adjustment. Start with the basics (fluid) and if that is ok, have a professional check your brakes!
    My brake light is on all the time in my 1996 ford contour is it the e-brake and how do I change it?
    My brother-in-law has the same problem with his. You better fix it fast or it will drain the battery.



    There is a piece under the brake pedal that is broken. You need to have it replaced. What happening is that even though you aren't stepping on the brake the contacts are meeting and therefore leaving your brake lights on.



    You can take out the fuse (when you're not driving) until you fix it.
    look on you break pedal and where it pivots or in the general area you will find you break light switch. It can be adjusted. check out the switch to see if it needs adjusting or may need replacing.
  • cs files
  • band myspace
  • Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?

    I think it might have something do with the signal lever seeing as it only seems to be the three lights operated by rotating the stick that dont work. Changing the fuse did not solve the problem... however the inside clock still works! when the stick is rotated off!! but as soon as i rotate for the lights to come on the clock goes off!! and obviously no lights come on!



    Indicators and brake lights still work.



    Is this an electrical fault or is there something i have not thought to check yet?
    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?
    The head lights could be burnt out ,my need to replace them . Have you tried changing the lights from bright to dim to see if you have one of the two,for as the dash lights go you may have the dimmer wheel turned all the way down %26amp; can't see the lights,because when you turn on the lights the clock light usually goes dimmer;

    Brake light out on 91 Jeep Cherokee?

    I can't believe I'm asking this, but how in the heck do I change my brake light in my 91 Jeep Cherokee? I opened up the rear door, and can not see anywhere to access the bulbs. The brakelight housing (is that what it is called?????) looks too complicated to get into, and I'm confused. Other cars I have had had easy access to the bulbs. Am I totally missing something here? Thanks!
    Brake light out on 91 Jeep Cherokee?
    Yess you are .... You need to take the lens itself off to get at the bulbs ... On my 89 that i had i think it was just two star screws ... Look closely at the lens to find the screws ... You will need to buy the right star screwdriver at any auto parts store... they should be able to tell you what size it is ... Your going to pull the entire lens out of where it sits and the wires are attached to it so be careful .... Just go nice and easy when you pull them out and you should be fine.... The bulb sockets are the kind that you twist to get out .... You should be able to do the whole thing at the auto parts store and that way you can get the right bulbs..... Good Luck ; )
    Brake light out on 91 Jeep Cherokee?
    No problem , glad i could help....

    Report Abuse

    How do i change upper brake light in a 1999 lexus?

    Not sure what year they went to LED lighting, but if it is a bulb assembly 鈫?

    Open the trunk. There will be a fabric liner around the taillight assemblies. It is held in by black push in fasteners. Carefully remove the fasteners. Gently pull back the liner to expose the lamp sockets. Twist to the left to remove.

    The same method applies for LED lighting except the bulbs are not replaceable. The whole asssembly must be replaced.



    禄禄禄

    I need help changing the rear left signal bulb and the rear right brake light.?

    This is for a 2001 volkswagen beetle
    I need help changing the rear left signal bulb and the rear right brake light.?
    If you are changing the bulb in the tail lamp, here is step by step instructions. open the trunk and look at the inside trim and on the left hand side is a black round cover take it off and look inside there is star shaped nut inside that you can remove with your hand (do not drop it, there is not any access to reach it) once the nut is off take a butter knife or something to wedge in between the lamp and the rear bumper cover to release the lamp. If you look at where the bumper cover and the fender meet there is a groove there, try to get under the tail lamp there. as far as the brake lamp, same process on right hand side
    I need help changing the rear left signal bulb and the rear right brake light.?
    I don't know if your car works like this, but for most cars that I know, you don't have to take off the red part of the light on the back. You go in through the trunk, possibly pulling off a carpet or plastic cover, then the bulb socket twists off from there. You change the bulb, twist the socket back in, then are done.

    How do you change the left rear brake light bulb on a 2004 IS300? How do you get to the bulb?

    go to your local toyota dealership, ask for a brake bulb, they will ask for you VIN. go to your trunk, open the panel, locate the bad bulb, take it out (two clips keeping it in) pull it out of the socket, replace bulb, cover it back up and hit the brakes if it lights up give yourself a cookie!
  • healthy hair
  • good tanning lotion
  • How do I change the rear brake light on my 2001 Ford Explorer Sport Trac?

    i own a repair shop and there's an access panel that you remove on it and it allows you access to the rear bulbs in it,you should be able to gain access to all of them ,and there's a panel for either side just in case you need to change one on either side of it good luck i hope this helps.
    How do I change the rear brake light on my 2001 Ford Explorer Sport Trac?
    Go to www.mysporttrac.com and I'm certain you'll get more answers than you need.

    How do i change the brake light in a 2001 Chrysler Town and Country?

    Open the hatch in the back, remove the four little bolts that hold the whole lens assembly to the vehicle, twist and pull the plug out that has the brake light in it, then remove and replace the bulb. Reverse to install. Should be a fifteen minute job for someone who has never done it before. piece of cake! GOOD LUCK!!

    How do I change BRAKE LIGHTS in a 98 Maxima?

    i have a 1998 nissan maxima and both of my side brake lights are out. i have replacement bulbs but have no idea how do change them??



    do i have to go through the trunk to open it?



    :-/
    How do I change BRAKE LIGHTS in a 98 Maxima?
    there are 2 ways depending on the model. Both ways are through the trunk. On some you can access the bulbs by twisting the plastic connectors off inside the trunk, and on others you have to unbolt the light assemblies from the trunk and then twist the plastic connectors out.

    SAAB 93 3rd Brake Light Change?

    Can someone please advise me how I change the bulb in the high level brake light on my 2000 (Year) SAAB 93 Convertible. The SID is displaying %26quot;Rear Brake Light Failure%26quot;. I cannot see how to access the bulb(s). Many thanks.
    SAAB 93 3rd Brake Light Change?
    Open the trunk and remove the trim and then you will have access to the boot mounted brake light, unscrew and remove to replace bulbs

    Volkswagen beetle brake light switch?

    Our 2001 VW Beetle has the epc light on we went to change the Brake Light Switch and now the brake lights are on constantly. Thinking it was a faulty switch we put the old one back in and it does the same thing. HELP
    Volkswagen beetle brake light switch?
    Make sure the switch you got is the UPDATED version. There were 2 recalls, so make sure (ask the dealer) if you have the most recent version. The replacement is covered under that recall, so you should just bring it in to dealer. Any extra cost, say scanning for error codes, would be extra. But the brake light switch will be free.
    Volkswagen beetle brake light switch?
    is your fluid level upto maximum.if low,top up and bleed the brake system.top up again to maximum level.now the lights would go off
  • howtodealwithhusband
  • nail polish swimwea
  • How to turn off the wear brake pad dash light of my Vectra?

    I changed the brake pads of my Vectra but the wear brake pad light in the dashboard brights still. Can anybody tell me the procedure to shut it off? I have read that some BMW models turns off the lights after spending 40 seconds with the driver door open with ignition key in the second position. I also have heard that there is an Internet site where I can find these procedures, Can anybody help me?
    How to turn off the wear brake pad dash light of my Vectra?
    call a BMW dealer ask them they will tell you
    How to turn off the wear brake pad dash light of my Vectra?
    Have you tried the owner's manual?
    Try disconnecting the battery for 20 or 30 seconds

    How do you change the light bulb in a toyota Camry 1993? The brake light in the back window.?

    You remove the cover, either clips or two screws, remove the light, replace the light, re-install cover, good luck on this project.
    How do you change the light bulb in a toyota Camry 1993? The brake light in the back window.?
    sometimes you gotta go open the truck and reach your hand up under the bulb housing to get the bulb, then push in and twist to get the bulb out. Thats what I had to do with my friends 93 Corolla.

    How do you change a driver's side rear brake light ?

    My drivers side rear brake light has just gone and i need to change it. How do you do it and what bulb do i need ? Oh yeah my car is a 2004 Voltswagen polo TDI
    How do you change a driver's side rear brake light ?
    Do it yourself. I don't know about ur car but with most all you have to do is look around and you will be able to figure it out. If there are screws on the outside of the tail light remove them. If none there go into the trunk and look for some wing nuts. You may have to pull loose some cloth cover, which is usually held on by Velcro to get to the nuts or screws. (If you're lucky you may find inside the trunk behind the tail light to be the wires that go into a socket thingy that you just twist and it will pull out with the bulb on it.) To remove most bulbs you push in on it and turn it. Look first and you should see two brass nipples on the bulb that hold it in the socket. Once you remove the bulb look at the filaments in it. Hold it up to a light source. If they are not broken you may just need to clean the connections. You can do this with a pencil eraser. Just rub it on the connections real good. Plug back in and check it. If you need a new bulb the number for it will be on the light itself or the metal part of it. Most brake lights have a double filament in them, that's what makes them brighter when you push your brake. It's pretty simple to do. Give it a try. You can't really hurt anything by trying.
    How do you change a driver's side rear brake light ?
    Take it to Halfords, they will change it for you while you wait. Watch how they do it so that you know for next time. They only charge a few bob. Good luck.

    How to change rear window brake light?

    i have a Hyundai sonata 1996 and it's brake light on the rear window is out and i was wondering if anyone knows how to change it?
    How to change rear window brake light?
    Open your trunk and look underneath the light- the bulb is probably accessible there.
    How to change rear window brake light?
    you want to change the bulb? the cover either pops off or there are 2 screws that needs to come out.
    you can call the dealer and ask a mechanic, but I guess it pops off if you cant see any tiny screws, ask the guys at the parts store to help you!! Man women have all the perks!!!lol,best of luck

    Why does my brake light stay on in my 2001 Nissan Maxima?

    I just changed the rear brakes on my 2001 Nissan Maxima by procedure and the Parking/ Emergency brake light continues to stay on even though the handle is in the down position. The light was not on before the repair. Please help!
    Why does my brake light stay on in my 2001 Nissan Maxima?
    Watch the light it should dim slightly when the parking brake is lowered. IF so the fluid level under the hood may be just loe enough to turn on the dash warning lamp. Only use DOT#3 brake fluid from a new container. Not out of that old rusty metal can in the back of the garage.
    Why does my brake light stay on in my 2001 Nissan Maxima?
    I don't know specifically about that car but it sounds like the emergency brake is not fully released even thought the handle is all the way down . If a cable is involved I would look for slack or a stuck cable
    You probably need new brake pads. When the pads get low enough, it makes the fluid level go down low enough and the brake light to come on.
  • networking
  • reptiles
  • Check engine and abs brake light on in dodge dakota?

    99 dodge dakota 5.2 v8 4wd speedo doesnt work until 40ish and check engine light plus abs brake light are on changed both sensors but still nothing.
    Check engine and abs brake light on in dodge dakota?
    Hook it up to a OBD2 scanner

    How do I change the brake light on the left side of a 1996 toyota camry?

    open trunk and go through the carpet. there should be a cut away already there
    How do I change the brake light on the left side of a 1996 toyota camry?
    If you have the manual that came with the car its in there. If you dont have it, it might be online somewhere. But yeah its gonna be in the back under the carpet probably.

    How do I change a brake light on a 1997 GEO Prizm?

    Probalbly through the trunk.

    There should be a socket/connector visible if you look for them.
    How do I change a brake light on a 1997 GEO Prizm?
    take the nuts off the tal light housing studs in the trunk..



    once you get those off, then the whole tail light assembly pops off the back,



    Unscrew the bulb from the housing



    then replace the bulb... make sure the bulb is firmly seated and then test the tail light by stepping on the brake, and turning on your flashers...



    If the reverse lights dont work replace them while you have the tail light apart, and double check by turning the key on but not startting the engine...



    apply the parking brake fully, and after making sure the car wall not roll, then shifting into reverse and checking the lights.



    if everything works then just reassemble the tail light back into the fender panel.

    Monday, September 19, 2011

    How do i take the rear light clusters off my 02 plated audi a4 avant to change the brake light?

    Look inside the trunk. There us usually easy access inside the trunk to change light bulbs in the rear lights. You might not even need any tools to do it.
    How do i take the rear light clusters off my 02 plated audi a4 avant to change the brake light?
    you should be able to get in from inside the boot,other wise just remove the lens.
    How do i take the rear light clusters off my 02 plated audi a4 avant to change the brake light?
    I have an audi A6 from the same year, and i changed the taillights myself. On my car, you open the trunk, and open the little compartments on the side. There, you can see the back end of the taillight. There is this little plastic piece that has the bulbs that is attached by a little plastic clamp to the taillight itself. The good news is that if you press in the sides of the clamp yourself, the plastic piece can be removed and you can take out the bulbs without any tools. The bad news is that it takes A LOT of effort to remove that little black piece. There were also some screws around the back end, but that removes the entire taillight, which is not what you want.
    Open the trunk/boot and remove the access panels one each side you have to depress a plastic clip holding the rear light bulb assembly in then simply replace the bulb.

    How to change the brake light bulb on Mk V Golf GTI?

    go to vwvortex.com
    How to change the brake light bulb on Mk V Golf GTI?
    That is quite a new car - you cannot have mislaid the owner's handbook already.



    RTFM - Read The F***ing Manual.
    How to change the brake light bulb on Mk V Golf GTI?
    go to the back of the car.

    open the trunk.

    Lift the carpet inside the trunk( if there is one) in the area where the lights are.If it is covered by plastic, there should be a way to remove it to access the light module.

    First have someone press the brakes while you are there, and figure out which light is out.

    If you are not sure turn on all the lights( driving lights) and have someone press the brake( it will be easy to figure out which bulb is out)

    You can get the light bulb out by twisting a plastic knob( remember, check the position of the bulb beforehand or you will end up replacing a perfectly fine one).
    or go ahead and open your truck and from there look at it and see how u will be able to take em out.. try figure em out.. it no hard.. just couple screw here and there and u will be able to take em out.. hoo ur bulb burn out fast ahh.. goodluck.. dont be afraid to do it yourself, i garuantee u if u do em u will feel so great.. if need more info just go vortexx..
  • get rid of blackheads on nose
  • how to remove a trojan
  • How do you change the rear brake light bulb on a 2006 Pontiac G6?

    Look in the owners manual, they have the instructions there.
    How do you change the rear brake light bulb on a 2006 Pontiac G6?
    If I had the manual, I would not have posted the question.

    Report Abuse


    How do you change the rear brake light bulb on a 2006 Pontiac G6?
    I have a 1997 Pontiac Bonneville SSE and you have to do it from the trunk. It is easy to do but takes a little work.
    go into the trunk and look for the plastic %26quot;wing%26quot; nuts holding on the tail light lense to the car. the whol thing comes off as a unit. and you go further from there. be careful with the plastic,,the tabs break easily.
    pull into a service station, ask them how much it cost. pay them.

    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?

    I think it might have something do with the signal lever seeing as it only seems to be the three lights operated by rotating the stick that dont work. Changing the fuse did not solve the problem... however the inside clock still works when the lighs are off but as soon as i rotate for the lights to come on the clock goes off!! and obviously no lights come on!



    Indicators and brake lights still work.



    Is this an electrical fault or is there something i have not thought to check yet?
    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?
    the first thing that comes to mind is. Make sure that the dimmer switch is not in the dimmest position as for the driving lights well like the last guy sed so rudely we need more info but may still not be able to help
    Driving lights and dash lights dont work. indicators and brake lights DO work, tried changing the fuse....?
    Your car/truck is WHAT YEAR/MAKE/MODEL?



    We can't read your mind.

    How can I remove the brake pad wear indicator light - k32?

    Hi, i just changed brake pads on my 2003 volkswagen jetta and this light came up on my dashboard which is the brake pad wear indicator light. My brakes are working just fine i dont see any malfunction but this light wont go off, is it normal to be showing up? How can i remove it? Thank you!!
    How can I remove the brake pad wear indicator light - k32?
    If you didn't clean the sensors and check the wiring connections, you need to do that. Remove and replace the ABS fuse to reset the sensor. If you disconnect the battery, you have to reset your clock and radio and all other electronic gadgets.
    How can I remove the brake pad wear indicator light - k32?
    disconnect the battery for 20 min to reset computer
    Did you replace the sensor. If it has one wire and touches ground it completes the circuit and the light comes on. If it is a two wire sensor and there is a break in the connection you should replace the sensor. I hope this helps.

    Change brake light on 03 Lincoln LS?

    I bought the replacement bulbs but I can't figure out how to change the bulb on the driver side. Can anybody tell me how to do this please?
    Change brake light on 03 Lincoln LS?
    Open the trunk and remove the carpet like lining that covers the rear area where the bulbs are and remove the old sockets and install a new bulb in the one that is bad.

    How do i change the 3rd brake light on my 07 toyota avalon (in detail)?

    I've tried popping up the plastic piece in the back, but it won't come up. The dealership wants to charge me a lot of money for something I can do myself, so if anyone knows how to get access to the light let me know.
    How do i change the 3rd brake light on my 07 toyota avalon (in detail)?
    I just recently replaced the same light in my Camry. That little cover simply pops off. use some force.
  • web server hosting
  • home search a scam
  • I have a 1994 Plymouth Acclaim where can i find info to change the middle brake light?

    I have looked through Chiltons book and there isnt anything in there.
    I have a 1994 Plymouth Acclaim where can i find info to change the middle brake light?
    there is just 2 screws in the housing or a retainer clip to remove the cover from it.. you do it from inside the back seat take the cover out and replace the bulb... it is a 921 bulb avail at any parts store
    I have a 1994 Plymouth Acclaim where can i find info to change the middle brake light?
    The one in the rear window? There are clips that hold that plastic case together. You have to open it up to remove the bulb.

    HELP!! HOW DO U CHANGE A BRAKE LIGHT BULB ON A 2006 EQUINOX?

    Tell me how to get the cover off. I need to change a light bulb on a brake light on a 2006 chevy equinox!!! I mean in the tail light section? Help help help!!!!!
    HELP!! HOW DO U CHANGE A BRAKE LIGHT BULB ON A 2006 EQUINOX?
    If there are no screws on the outside.Open the trunk.You will need to take out or pull back the carpet like walls directly behind where the tail light is..There should be up to 4 plastic wing-nuts or 4 nuts.you will need to take off.If you can get to the bulb from the trunk go ahead,but you probably will need to take the entire tail light out.
    HELP!! HOW DO U CHANGE A BRAKE LIGHT BULB ON A 2006 EQUINOX?
    open up the hatch there should be 2 phillips head screws on the inside. if that isnt right try seeing if there is an access panel inside that will give you access to the back of the lights without actually taking the light off of the vehicle
    I dont know... but you should have sex with the chick ur doing it for

    How do I change the bulb/brake light -Toyota 4-runner (1992)?

    I cant find an owners manual and I cant figure out haow the lens cover comes off. I would also be interested in a free download of an owners manual.
    How do I change the bulb/brake light -Toyota 4-runner (1992)?
    There should be either a small screw or clip behind the light housing itself.

    How do you change a brake light in a 2003 PT Cruiser with the Custom PT cover on it?

    Slightly pull the back of the cover to reveal the screw towards the back of the light assembly just below the brake light. Use a star wrench or you can use a straight screw driver, preferably one that has a bend to it. It will be difficult to get much room in there, you don't want to pull too hard to break the adhesive grip. When you have the screw loose, you can pull the light assembly out and replace the bulb. Then put it back in place and gently adjust the cover so you can screw the screw back in. That should work for you.
    How do you change a brake light in a 2003 PT Cruiser with the Custom PT cover on it?
    open rear hatch the brake light is held on with 2 screws or push pins pull lamp out change bulb hope this helps

    How do you change the brake light switch on a 1994 geo prizm?

    Under the dash drivers side above the brake pedal you will see a switch attached to the brake pedal arm. This is the switch that you want to change. There is a clip and a electrical connector and that is about all there is to it. Just be sure to put the pieces back in the same order that they came off. Check to make sure that the switch contacts the contact plate enough to depress the switch.
    How do you change the brake light switch on a 1994 geo prizm?
    Inside the trunk is 4 little plastic Wing-nuts you pull off to get inside the light fixture.
    How do you change the brake light switch on a 1994 geo prizm?
    hey wouldnt a brake light switch on a 94 prizm be more than the prizm itslef? im sorry i couldnt resist. I really an sorry...the only reason i said anything is because i have one too....again i apoligize for the smart *** answer.
  • networking
  • best advice to give girl
  • How do I change a brake light bulb on an x reg audi a6 1.9 tdi?

    Inside the boot or trunk 2 removable panels take these out and the bulb Assembly's can be removed and the faulty bulbs replaced.Have an Audi Mick UK.
    How do I change a brake light bulb on an x reg audi a6 1.9 tdi?
    You have to be more specific. What yr? Is it a sedan, suv, how many does it seat? I know you want to replace your brake light bulb but it would make my job a whole lot easier to find a manual for you. I tried researching it in the free manual section online but without the year of the car it is totally pointless.
    How do I change a brake light bulb on an x reg audi a6 1.9 tdi?
    in the boot there is a plastic cap in line behind the light, remove the cap and you will see a star bolt, unscrew that and need to pull your whole light out from outside, unclip the bulb holder and replace the bulb

    How to change left hand stop/brake light on 1994 Subaru Impreza?

    I have a 1994 Impreza Sedan. How do you remove the light casing to replace the bulb? I can't see any screws or bolts because it is all covered.
    How to change left hand stop/brake light on 1994 Subaru Impreza?
    You probably change them from the inside of the trunk. I do on my '96 Legacy.
    How to change left hand stop/brake light on 1994 Subaru Impreza?
    Inside the trunk, move the cover near the light on the inside of the trunk. You can see the access from there. There may be some of those little pop out plastic connectors that you might have to remove.

    HOw do you change a brake light in a 2005 pontiac bonneville?

    Bonnie's tail lights come out from the inside of the trunk. Fold back the insulation and twist the electrical bulb holder. The light bulb pulls straight out. Dab a bit of silicone ignition grease on the contact points of the new bulb to prevent corrosion.
    HOw do you change a brake light in a 2005 pontiac bonneville?
    THROUGH THE TRUNK
    HOw do you change a brake light in a 2005 pontiac bonneville?
    yes in the trunk...there might be screw tabs...take these off and and the tail lite can be removed from car..then unscrew lite and replace in reverse

    How do I chnage the brake light on my 2006 VW Beetle Conv?

    I have to change my right rear brake light. Does anyone know where in my trunk I need to go to find the brake light assembly?
    How do I chnage the brake light on my 2006 VW Beetle Conv?
    Remove the black circular plastic covers along the back of your trunk on either side. Behind these covers you will find a big plastic nut that holds the tail lights in place.

    How do I change the brake light bulb in my 202 Kia Spectra GS?

    most cars have cutouts/covers on the back of the trunk that lets you access the bulbs. Go to an auto parts store, look up your vehicle and get a new bulb. Remove the plastic cover, and remove the bulb/harness from the tail light (usually just a twist), the bulbs usually just twist out of the bulb socket also. Then reverse to install and check the light to make sure it works.
    How do I change the brake light bulb in my 202 Kia Spectra GS?
    If you are asking such a question then you dont have any form of mechanical experience so take the care to a mechanic shop and have the thing done properly.
  • thin hair
  • pimp myspace
  • I had my brake light switch changed and from it car seems to be losing acceleration help?

    this only happens after about 10miles and her brake seems to be stiff one minute loose the next do you think it has something to do with brake light switch or something more serious
    I had my brake light switch changed and from it car seems to be losing acceleration help?
    something else thats like saying you replace a light bulb in bed room but has no hot water
    I had my brake light switch changed and from it car seems to be losing acceleration help?
    The brake light switch should not affect the operation of your brakes.



    However, check to make sure there are no wires hanging down and interfering with your brake pedal. There could be more resistance on the brake pedal if something gets wedged.



    Otherwise, start going over your brake system.
    the brake light switch would have nothing to do with the problem your having, you have some other problem.
    It can happen. Some cars automatically turn off overdrive when you hit the brakes so the engine will help slow the car. If the old switch was on all the time, overdrive would never engage and you'd have better acceleration because you'd always be in third gear. Fix the switch and overdrive works again, reducing response quite a bit on the highway.

    How do you change a brake light bulb in a citroen picasso?

    you have to take the full light cover off. to do this when you open the boot lid look on the panel right behind the light cover you should see a panel that can be opened when you open this you will see all the wires leading into the light cover. It's quite awkward to get into. you should be able to see or feel the clips on the light cover unhook the clips once you do this the full light cover will release, take it out and you will see all the bulbs change the one you need changed then replace the light unit. Be care full when doing this as the clips are quite brittle and stiff. easily broken. hope this helps

    How do I change the brake light switch on a 98 chevy silverado?

    It is located underneath the steering wheel where all the wiring is. Get a flash light and stick your head under there. If you have a new brake light switch use it to help yoru find the new one by the way it looks or feels. I do not know off the top of my head how to adjust the brake switch though. Do not install a new one until you figure out how to adjust it.
    How do I change the brake light switch on a 98 chevy silverado?
    Some things need to be done by a pro.Please take your chevy to a dealership and let them check the stop lamp system to correct the problem.There is more to it than think.

    How do I change a brake light on a 2006 chevrolet impala?

    1800-safe-auto
    How do I change a brake light on a 2006 chevrolet impala?
    got to go in through the trunk
    How do I change a brake light on a 2006 chevrolet impala?
    Screwdriver?
    Too vague a question. Is it the regular brake lights or the third brake light. You take the cover off and remove the bulb. If you are not capable of doing this, I think autozone does this for free in their parking lots
    Open the trunk: (1) there are 2 or 3 plastic screws easy to grip (2) after removing them (3) pull back the inside covering (4) there will be a couple more plastic screw handles to twist off, remove them (5) from outside pull the entire light Assembly off. (6) turn on head lights and 4 way flashers. (7) there should be three light sockets just twist each one off to what light bulb is not working. Also before buy a new light bulb. Buy some light bulb grease and put some grease in the light that is not working and reinstall the light. Most of the time this works. If the bulb is black and looking burnt change bulb. Chevy has these problems with lights going out.

    Change a 2005 Kia Rio Brake Light?

    How Do I pop the light off and change the brake light? Thanks!
    Change a 2005 Kia Rio Brake Light?
    Try from inside the trunk

    http://www.haynes.com/video.downloads

    http://autorepair.about.com/cs/troublesh鈥?/a>
    Change a 2005 Kia Rio Brake Light?
    well if you have the new one with you then you can see that it has like two small arms so you have to push it in and then turn it easily to the right and it should come out easily good luck
  • silk comforter
  • row cell
  • How to change brake light in 2002 trailblazer?

    Open the hatch and remove the phillips head screw holding the tail lamp housing to the truck pull gently and the light should come out then you may need either a phillips again or possibly an inverted torx socket to take the circuit board off of the housing so you can access the bulbs.
    How to change brake light in 2002 trailblazer?
    Quite simple. Lift the rear hatch and pull back the panel...I can't remember on that GM if there's a way you can pull off the tail light assembly, actually it is. And you can pull it off and slide a new bulb into the connector. Good Luck!

    How do you change the brake light bulb in a 2002 dodge intrepid?

    pop the trunk, whatever side the light is out on theres a plastic piece pull it back you probably have to twist and pull the light. then replace with new one twist opposite way
    How do you change the brake light bulb in a 2002 dodge intrepid?
    Easily, ask a male to do it. They always want to please women. It doesn't matter what task. They like to feel good about themselves. Women vs. men kind of thing..

    Or, if you're independent? Open the trunk and unscrew the back partition thats sometimes locked in place. (will require a phillips head most likely) Don't try to force the back covers off. That usually isn't the right place to start.

    Also, try Autozone, they usually will change it for you in the parking lot...They also check batteries, fuel lines/pumps, add water to radiators. They are very helpful for some reason...
    How do you change the brake light bulb in a 2002 dodge intrepid?
    You are female so go to Auto Zone or Advanced Auto or Napa and act like you don't know what is going on but you want to learn. Ask them to show you how so you will know the next time. Pay attention so you will know the next time but they will do it for you. Next time too probably. lol

    How to change the cyclops brake light on a 1997 Jeep Grand Cherokee?

    Remove %26amp; install a new ' cyclops ' light.

    How do I change a Brake Light bulb in my 2009 Jeep?

    what model jeep ?


    usually you remove the tail light and then pull the sockets out.

    How to reset low brake pad warning light for 2007 bmw 750i.?

    We changed brake pads and sensors, front and back...but the low brake pad light is still on. How do we reset the light?
    How to reset low brake pad warning light for 2007 bmw 750i.?
    try unhooking one of the battery cables for a minute and then hook it back up.
    How to reset low brake pad warning light for 2007 bmw 750i.?
    i think u might have to take it to a dealer for it to be reset i havent heard anything on the new bmers or talk to a mech that works at bmw
    check your owners Manuel.
    I have the reset procedure but it's a bit long winded so if you can give me your e:mail address I will sent it to you as an attachment.

    frankiegardener@yahoo.co.uk
    under the steering wheel on drivers side there is a panel remove it, there is diagnosticplug ,stick scantool in and clear code .
  • get ride of my dry skin
  • celebrities myspace
  • How do i change a brake light?

    are all brake lights bulbs the same?
    How do i change a brake light?
    No not all bulbs are the same. And is it a tail lamp bulb or third brake light? What kind of car is it? What's the year? If it's older, your probably going to need an 1157. Newer cars use either a 2057 or 3157.



    If the owners manual doesn't say which, you will have to access the back of the tail light and remove the worn bulb and see what it is.
    How do i change a brake light?
    Depends on the vehicle. Most you access through the trunk or the hatch. Some you may have to remove the tail light assembly usually held on by nuts located in the trunk.



    No all bulbs are not the same you need to get the correct bulb for your vehicle.
    No, they are not the same. Can't help you with the change because you did not indicate the vehicle.



    禄禄禄
    A lot of cars use the same ones, but some dont. Just ask the auto parts counter guy to look it up for your model. Usually theres some plastic wing nuts inside of the trunk, behind the brake lights. Once you remove those, the entire housing comes off by gently pulling on it from the outside.



    Before you put it all back together, turn your parking lights on and make sure its dim like the others. If that brake light bulb is lit up very brightly and the others are dim looking, then you have it backwards, take the bulb out and turn it 180 degrees and plug it back in.
    Hahahaha notice how the other guys were helpful and the mechanic was the rude, unhelpful one!



    But yeah, look in the trunk, sometimes under the carpeting for the screws or bolts to remove the taillight assembly, take out the burnt out bulb and use that to match to a new one in the store! Good luck!
    yes there are kits that they sell at autozone ect.,





    depending on ur car you just have to open ur trunk and find the screws and open it.

    EPC light on my 04 Volkswagen bug came on changed brake light switch still on /no brake lights help?

    The EPC light is a warning for the electronic throttle valve. The brake light switch is only one input for the system. Are you sure it needed or needs a brake light switch? Did you check fuse S13 in the fuse/relay panel? Has it been checked for diagnostic trouble codes? Generic OBDII won't tell you anything. It needs to be checked using a factory or VAG capable scan-tool.

    How do I change the brake light on a 2003 Jeep Liberty? I can't see how to gain access to the bulb.?

    To change the bulb you have to open the tailgate and use a torx T15 screwdriver and remove either 2 or 3 screws holding the lens in. Then pop out the lens once the screws are removed. Next disconnect the electrical connector for the brake light, turn the plastic piece that the wires were connected to and pull once it stops turning to the left. The bulb should now be in your hand. Installation is opposite of removal. Hope this helps.
    How do I change the brake light on a 2003 Jeep Liberty? I can't see how to gain access to the bulb.?
    pop truck open the lights boxes pop out... its hard
    How do I change the brake light on a 2003 Jeep Liberty? I can't see how to gain access to the bulb.?
    well you need to install the light so its easier to access the bulb. it will be much easier to change that way
    The best thing to do is to get a Chilton's book for that year and model. It will be step by step. Good luck!!
    my SUV i remember you had to open the back gate, then unscrew the light fixture and pull it from the car so you could get to the back of it and change the bulb. there wasn't any little door to reach in and pull the bulb like on a car

    Why is my 1999 Nissan Sentra's brake light is on in the dash board.?

    My Nissan Sentra's brake light is on in the dash board even after releasing the parking brake. There is no change in the braking, No noise and brake paddle is still up instead going inside. I suspect its the problem of low brake fluid. %26quot;Just Brakes%26quot; has give a quote of $150 for checking any leaks, changing brake pads if necessary. Tell me what must be wrong firts of all and is $150 a reasonable quote for brake service.
    Why is my 1999 Nissan Sentra's brake light is on in the dash board.?
    Go to a mechanic emidiately
    Why is my 1999 Nissan Sentra's brake light is on in the dash board.?
    Your brake light has most likely gone bad. Have a friend stand behind your car as you push the brake pedal. See if the rear lights get brighter.

    Many of the bulbs have two different wattages. One for normal driving and then a higher wattage for braking. You won't really notice if the higher wattage part of the bulb burns out, but your car knows.
    its 2006 time 4 a new car
    If the $150.00 includes replacing the pads, yes, that is reasonable.



    The light can come on for several reasons. Some of the most common causes are low brake fluid, short in the electrical system, a bad bulb, or an ABS problem. It could also be a main booster problem if you have power brakes.



    I would let a technician do an inspection and service for $150.00 with no problem....but I would call the dealer first. This is because if you still have any warranty, the problem MAY be covered. Also, dealers are becoming more competetive on routine maintenence and are not as high as they used to be. In addition, the dealer warrants repairs easier than independent shops and have the latest diagnostic equipment for you specific car.



    Good luck and happy motoring!
    Brake light could be a sign of brakes wearing out. A 99 should be close to expiration. If there are leaks. Pump the brake pedal and check for liquid near the tires. If you pull on the emergency brake and it goes all the way up pretty easy, it is a good sign that your brakes are needing repair.
    All of these answers are good but here is one not listed.

    Check the emergency break. If it is on even 1 notch, eather by foot or by lever it will also turn on the break light on the dash

    '

    How do I change the brake light in a 2002 Hyundai Accent GS?

    either you will need to take 2 screws holding the light in that are locates in the plastic housing of the tail light(will be visible with truck/hatch open) or you will have to take a little access door in the trunk behind the tail light that will have a few nuts holding the tail light on, simply remove either the screws or the nuts pop the light out and twist the bulb so it will come out,then replace it and reverse the steps to get it back in



    good luck
  • advice and suggestions
  • good relationship advice
  • How do i change a brake light on a 99 grand am?

    the middle brake light bar, the one on the trunk, i know where the bulbs located and stuff, but do i have to unscrew those plastic lookin screws, or is there some sort of clip or something
    How do i change a brake light on a 99 grand am?
    I think those plastic looking screws either screw or just pop out with a small prying tool like a small screwdriver. Then, behind those, are a real screw on each side that holds the housing to the body sheet metal underneath. Once you get those, you should be able to pull off the housing and replace your bulbs.
    How do i change a brake light on a 99 grand am?
    you should have a screw on both sides of the light. take them out and it should come right off or it could snap off.

    Changing the high tail brake light bulb on a peugeot 206?

    Open the boot and you will see 2 small nuts on the top section of the boot remove these and push the light fitment out of situ this will allow you access to the bulb housing. Ps previous answer incorect you can change the bulbs but they have a tendancy too stick
    Changing the high tail brake light bulb on a peugeot 206?
    i think you have to change the whole unit refer to main dealer

    How do you change the rear brake light bulb on a 2001 mitsubishi montero?

    I have a 200 Montero (not Sports). The right brake light is out. There is no easy way to access the light. no opening for me to reach in from the trunk to just turn the light bulb and remove it. there are two face plate screws. I unscrewed both and still unable to remove the face plate.....help anyone?



    thanks.
    How do you change the rear brake light bulb on a 2001 mitsubishi montero?
    there are the two faceplate screws, but there are also a couple of snap-in pins on the back of the lens assembly. after removing the screws, CAREFULLY take a flathead screw driver and slide it between the edge of the lens and the car body. then EASILY pry towards the lens. as it moves out, slide the flathead further behind it so as not to put all the pressure on the lens itself. it should pop out. then you replace the bulb, snap it back in, and replace the screws.
    How do you change the rear brake light bulb on a 2001 mitsubishi montero?
    no problem. anytime

    Report Abuse


    check inside the car look for a removable panel that will be directly behind the brake lights



    pop that off then you will have access to change the bulb

    How do I change the brake light bulb on a 2002 Mitsubishi Galant?

    Open the trunk and fold down the carpet behind the light take the plastic wing nuts off and the lens will come out.Then do the reverse.

    How do I change the brake light in a 1994 Chevy Cavalier? There is no apparent access through the trunk.?

    If the lights are in the body and have no screws on the outside:



    When you open the trunk you will need to pull the carpet back at each corner where you can get to the tail lights. There will be a plastic connector that pushes into the back of the light and turns 1/4 of the way around to lock. Give it a twist and remove it. The bulb will then pull out of that connector and you can replace it. Installation is reverse of removal. You can also go to the local library and check out a repair manual on your vehicle. Good Luck.
    How do I change the brake light in a 1994 Chevy Cavalier? There is no apparent access through the trunk.?
    The access is through the trunk on the deck lid (trunk door). You unscrew the light retainer and the wire and light comes out. Change the light bulb, and put it all back together.



    I changed my gf's brake light in her cavalier a couple fo weeks ago.
    How do I change the brake light in a 1994 Chevy Cavalier? There is no apparent access through the trunk.?
    If you're a girl, take your car for an oil change, then kinda tilt your head to the side and ask the service guy if he has any idea how to do it. They'll do it for you.
    There should be (plastic)nuts in the trunk , take them out and the light asbly.should come out.
    look for an access panel that is on the side of the rear of the trunk,,there are little screws that u have to take off,,it will be directly behind the light
    Attack this one from the outside.
    The entire lamp comes off as an assembly. Should be some thumb screws/nuts inside trunk, loosen and pull lamp away from body.
    its hard for me to understand why women think they know everything, when something this simple has you befuddled.
    Look up 1994 Chevy Cavalier and how to replace the light on line
  • lock file
  • medium length hair
  • Lost owner's manual. How do you change brake light on 2005 Chevy Equinox?

    These are the instructions from the book.

    1. Remove the tail lamp screw covers. (located on assembly when back gate is lifted.)

    2. Remove the tail lamp screws.

    3. Carefully slide the tail lamp housing outward to clear the stud and then rearward and away form the body of the vehicle.

    4. Turn the affected bulb socket counterclockwise to disconnect it form the tail lamp housing.

    5. Pull the bulb out of the bulb socket.

    6. Push the new bulb into the bulb socket.

    7. Insert the bulb socket into the tail lamp housing and turn it clockwise until seated.

    8. Re-install the tail lamp housing to the vehicle, install the tail lamp screws and screw covers.

    Hope this helps.
    Lost owner's manual. How do you change brake light on 2005 Chevy Equinox?
    1. Remove the tail lamp bolt covers (2). Open the rear door to access them.



    2. Remove the tail lamp bolts (3).



    3. Pull outward at the front of the tail lamp assembly to disengage the retainers from the body side.



    4. Remove the bulbs from the tail lamp assembly.



    5. Remove the tail lamp assembly from the vehicle.



    6.Replace the bulb by twisting the socket.

    How to change the rear brake light bulb on a 93 Mitsubishi 3000 GT?

    I open the plate behind the light (inside the trunk) but couldn't find the socket. It looks like the entire light assemble is sealed with the body. I heard that it needs to take out the corner piece of the body to change the blub, but not sure. Cannot find any shop manuel. Please help.
    How to change the rear brake light bulb on a 93 Mitsubishi 3000 GT?
    You need a professional to do that.
    How to change the rear brake light bulb on a 93 Mitsubishi 3000 GT?
    pull the panal out. dont worry it wont break but if you cant go to a garage
    I have a 95, and if your is like mine, right above the tail light is a small fiberglass piece. That piece DOES have to come off too, but it's just held on by a couple of bolts. Other than that, the light is not molded into the body, but you might have to stick your hand back there in the trunk to find the rest of the little wing nuts holding it on. Chances are, if the light has never been removed it will be kind of tough to get out. Just a little pressure will do the job.

    How do i change the brake light in my Mk5 VW Golf 1.4s 56plate?

    it seems when i move the carpet out of the way, there is just metal? how do i cahnge it?

    many thanks
    How do i change the brake light in my Mk5 VW Golf 1.4s 56plate?
    There should be a plastic plate behind the light cluster in the boot but if not, then the light cluster will be screwed in from the outside. Don't get a BMW.
    How do i change the brake light in my Mk5 VW Golf 1.4s 56plate?
    these golfs like peter said normaly have a plastic part which is where the bulbs are held in and ovioulsly have the wires plugged in and thats held in by the light itself u just need to uncatch all the clips/catches and it should be as easy as that. if u wana take your whole light out then the light is held in by two bolts in the car, undo then and it will just come off.



    can never be too sure i spose :-)
    Its called a mechanic find one.
    you need to scap it and get a bmw

    HOW DO I CHANGE BRAKE LIGHT SWITCH 2001 FORD ESCORT?

    My brake lights will not go out after I turn the car off,
    HOW DO I CHANGE BRAKE LIGHT SWITCH 2001 FORD ESCORT?
    Under the brake pedal........unplug the old one..........plug in the new one.
    HOW DO I CHANGE BRAKE LIGHT SWITCH 2001 FORD ESCORT?
    the switch is located half way up the brake pedal and most times it comes loose,or slips out of place

    How do you change the brake light in an 05 toyta sienna?

    http://www.autoall.com/images_products/U鈥?/a>



    Thats what it looks like. I can remove the two screws that are visiable but then it appears to still be clipped to the body. I cannot find how to release it so that i can change the tail light.
    How do you change the brake light in an 05 toyta sienna?
    it probably has those plastic clips helping hold it it. if you can get a screwdriver in use it to work the clips out. i worked at a ford dealership and when i had to replace lights i would always get new clips cause its just easier to rip them out and replace with new ones. but make sure you can do that first( get parts first).
    How do you change the brake light in an 05 toyta sienna?
    Buy the replacement.



    From the inside there are plastic parts. Use a screw driver to remove some parts, but most new vehicles have compartments where you can unsnap. It's pretty simple after you see the back of the light.



    Remember to put it all back together in the way you took it apart.
  • web hosting sites
  • ie
  • How do you change a brake light switch for ford escort?

    its located at the top of the brake pedal and if you never done one take to a shop, if you have cruse control there are vacuum lines up there and you don't want someone unqualified doing a change OK good luck, however they are not hard and don't require many tool just some mechanical knowledge
    How do you change a brake light switch for ford escort?
    UMMM.. you don't ..just throw the car away and go buy a new one :) hehe
    How do you change a brake light switch for ford escort?
    This is not a difficult task in it self. However the difficult part is just getting to it. By 18 year old daughter is on her second 1998 Escort. I have replaced the switch once on her first car. However on he second car I only had to replace the bumper bad that activated the plunger on the switch. It is pretty simple..plug and play. Just be sure you write down what wire went where and get a good measurement of the placement of the switch in the mounting bracket. Good Luck

    How to change a 2000 camry brake light?

    i need to change the brake light on the trunk door, not the one attached to the bumper... HELP
    How to change a 2000 camry brake light?
    This should be a simple fix for you. Open the trunk and remove the interior trim on the trunk lid, if my memory is correct, the clip has a center pin in it (just pick it out with screwdriver) and the trim will come off. The next step is to twist the bulb holder off the lamp (easy) and pull the bulb out, there is a number on it, use this to get your new one. good luck

    How to change a burnt out brake light bulb?

    How do you change a tail light bulb in a car?
    How to change a burnt out brake light bulb?
    you need to declare the car and model to find this out.



    Some older cars- take off the lens cap screws and change the bulb.



    newer cars- from the trunk.



    check the owners manual or just google

    %26quot;change brake light 1999 caravan%26quot;
    How to change a burnt out brake light bulb?
    go in the trunk and pull the carpet away from the back of the light...there is usually screws or grommets that you have to pop off and then the bulb slides out. it connects to its socket almost like when you connect a regular cord to an extension cord. the bulb will have the style of bulb that it is. Make sure you get this same kind. If you are really unsure go to an auto parts store and they will help you out.
    how about auto zone and maybe they will do it for ya

    How do I change the third brake light on a 2001 Hyundia Accent Hatch back?

    I don't have an owners manuel but, it looks like I'm going to have loosen two bolts and remove the whole light fixture it self. I was hoping there may be an easier way because the area I have to manevor in is tight and I'm a big guy.
    How do I change the third brake light on a 2001 Hyundia Accent Hatch back?
    If you dont mind Id visit your local highschool auto shop

    usually its good for the kids and they get more hands on traning



    plus they usually will do it free

    Wednesday, September 14, 2011

    Ford Fiesta 53 reg rear - how to change the brake light bulb?

    How can I change my ford fiesta 1.25 53 reg rear brake light. I tried undoing the 3 hex type head bolts but the light assembly doesn't want to come off. can you help please?



    thanks, Alan
    Ford Fiesta 53 reg rear - how to change the brake light bulb?
    Im a fairly old mechy but i dont remember a 53 fiesta. 53 Cresta maybe and there still the same bulbs Amazing
    Ford Fiesta 53 reg rear - how to change the brake light bulb?
    well it went in so has got to come out...if you have undone all the fixings mite just need a bit of gentle persuading then will pop out.it could be stuck due to foam sealer...
    I had this same problem.



    Stick your hand in the back behind the light, theres a plastic bit that you have to unscrew. If you just feel about below the seatbelt you should find it, its quite a long screw, takes a wee minute. Its fidgety!!



    Sorry i cant be more specific with the technical terms, but i'm sure you'll find it.
  • effects on relationships
  • programming
  • Is the dashboard meant to light up when I brake in my ford fiesta.?

    I have a 2003 ford fiesta and whenever I recently changed the brake lights and now whenever I brake the dashboard and front sidelights light up. Have i just never noticed this before or is the wiring mucked up
    Is the dashboard meant to light up when I brake in my ford fiesta.?
    no

    You either put in the wrong bulbs or put the bulbs in incorrectly.



    The base of the bulb has 2 contacts that should align with the contacts in the socket. One is for the taillight and the other is for the brake light. There are two prongs at the base of the bulb 180 degrees from each other, one is high and one is low. these orient YOU to put the bulb in the right way so that it locks into position correctly and prevents crossover.



    When you apply your brake the brakelight circuit is crossing over to the taillight circuit which is also lighting up your dash lights.



    go back and carefully check them. turn your parking lights ON for reference. with the Parking lights on only the dimmer of the two filaments should be lit, the brighter thicker one is the brake light.
    Is the dashboard meant to light up when I brake in my ford fiesta.?
    change your recently fitted bulb and either fit it the correct way or get the correct bulb, its earthing.



    have seen some bulbs were the 2 elements inside the bulb touch and make this happen.
    have you changed the standard rear light cluster for one of them clear so called lexus style?? if yes seems you got a earthing problem, make sure the rear light have a good clean cable going to the body as a earth...this should solve your problem....
    try putting a temporary ground on the bulb socket ,this is assuming you put the right bulb

    Audi TT rear drivers side brake light change, How do I get the light fitting out to change the bulb?

    I have unscrewed the two little handles and one side seems to want to come away but in the far side it is still attached what else do i need to unscrew to release the light fitting. im a girl by the way so please no mechanic jargon
    Audi TT rear drivers side brake light change, How do I get the light fitting out to change the bulb?
    In the trunk you've forgotten to remove a hold down nut. Pull the carpeting away and look for it. You'll see whats holding it if you use some common sense.

    You may have removed what is visible in the trunk but your gonna have to peel back the carpeting to see what you've missed. trust me you can do this.
    Audi TT rear drivers side brake light change, How do I get the light fitting out to change the bulb?
    Its the two screws and it also sits on one (or two?) little ball and socket type of attachments down in the recess. This is what makes it feel tight and does require a gentle but firm pressure to pop them out. But it does pop easily and a dainty lady should be well able to do it as well as a man !.
    Try :



    tt-forum.co.uk



    forums.audiworld.com



    audi-forums.com



    I hope this helps.
    non jargon - get hold of it and rag it out!



    if you have released the lamp unit then its probably just stuck on plastic dowels, you may need a bit of pressure to shift them.
    check and make sure there should be more knobs there maybe a little lower, some times the addhessive tends to not let go!!

    How do you change a brake light in a 2002 Lincoln ls?

    How do you get to the bulb
    How do you change a brake light in a 2002 Lincoln ls?
    In the trunk, pull back the trunk liner by the tailight desired for access. There are about 4 or 5 plastic wing nuts that can removed by hand. Once removed, the tailight assembly should just pop out place fairly easily. Turn the bulb connector desired for replaced about 1/8 to 1/4 of a turn COUNTERCLOCKWISE, and pull outward for access to the desired bulb. If it's the brake light bulb, the replacement you need is a CLB-3157.

    How do you replace brake light in 2004 jeep grand cherokee?

    Hi, I am trying to find out how to exactly replace the brakes bulb in my jeep. I have already gotten the bulb out i just need to remove it from its socket but cant seem to figure it out and i am trying to be careful because when i usually change light bulbs they end up breaking so im taking this one easy and looking for some advice on how to remove the bulb from the socket
    How do you replace brake light in 2004 jeep grand cherokee?
    Uhhh....If you're removing an old one, it doesn't matter if it breaks because it's going in the garbage anyway.

    How to fix brake light on a 2000 Jeep Grand Cherokee?

    My jeeps left side brake light has recently started acting up. The brake light works when the headlights are off, but when the headlights are on the left brake light will not light up. Tried changing the bulb but didn't help.
    How to fix brake light on a 2000 Jeep Grand Cherokee?
    Sounds like you have a bad ground at the rear lamp cluster. I'm not sure how your lamp unit will ground. In my TJ Wrangler it is grounded by the mounting bolts. Your's could be with a ground wire though. Make sure the is no corrosion in the actual bulb socket too.
  • Free php web hosts
  • msdn
  • How do you get inside the lens case to change the brake light of a 2004 Master Tow tow dolly?

    some have 4 screws that you remove to get the cover off or it might be a pressure fit and you need to pry it off with a screwdrIver I never did a tow dolly but ive changed lots of trailer bulbs
    How do you get inside the lens case to change the brake light of a 2004 Master Tow tow dolly?
    The whole plastic light assembly pops out of the rubber grommet and unplugs.

    Replace the whole light.....

    HOW DO I CHANGE BRAKE LIGHT SWITCH 2001 FORD ESCORT?

    My brake lights will not go out after I turn the car off,
    HOW DO I CHANGE BRAKE LIGHT SWITCH 2001 FORD ESCORT?
    All brake light switches are very similar to replace. Use the link to help you.



    http://www.ehow.com/how_6482836_replace-鈥?/a>
    HOW DO I CHANGE BRAKE LIGHT SWITCH 2001 FORD ESCORT?
    Try pulling up on the brake pedal and have someone watch the brake lights. If they go out then the spring is toast or the pedal is sticking. If they do not go out then yes the brake light switch is toast.



    The brake light switch is located on the brake pedal arm(between where you put your foot and the bottom of the dash) Usually you have to take out the pin that holds the brake pedal arm to the brake master cylinder rod. Look up under the dash at the brake pedal arm and look for the switch.

    How do you change a brake light bulb in a 1997 Honda Accord?

    there should be an access panel in the trunk. it either flips open on a catch, or there may be screws (but i doubt that last one).

    Flip open or remove the cover, twist out the socket that holds the brake lite bulb, remove the bulb, replace with new one (only goes in one way, so don't force it in), replace the socket unit, CHECK to see if it works first, then if all is well, close up the panel in the trunk.

    Can i change the brake light myself in toyota camry?

    99 toyota camry brake light went out,i looked it up on auto zone,only costs about $5.00,its the bulb.

    my question is can i do this myself?is it easy to get to?do i need any tools?etc.etc.thanks in advance to all you experts.i appreciate it as a single women not wanting to put out bucks for something simple.
    Can i change the brake light myself in toyota camry?
    Yes, just pop the trunk and look on the inside where the light is. It is just as simple as popping it out then in. Once you see it you will understand more. No tools are needed
    Can i change the brake light myself in toyota camry?
    The bulb is not hard to remove, you need to remove screws from inside the trunk then the lenz is removed giving you access to the bulb.

    The oil depends on if it is a 4 or a 6.

    The 4 holds 4 quarts and the 6 holds 5quarts.

    How do you change brake light bulb on a Toyota Emina?

    Ask a Blonde!
    How do you change brake light bulb on a Toyota Emina?
    Drive to the local garage
    How do you change brake light bulb on a Toyota Emina?
    Usually to change any car brake light is to access it from inside the boot. The bulb housing should just be held by simple clips. Undo these and you should get access to the bulbs
    Go into your boot remove the retaining clips and all the light cluster will come out of the body work make sure you change the right bulb
    open the boot.look inside and on the left and right you see what is called the bulb cluster..this is just a fancy term for where all the bulbs are....you should see a release clip..its usually part of the plastic body, this is pressed and the cluster is released.jiggle the cluster out..identify which bulb it is...some have two filaments in the bulb some cars one filament..they are about 50p each...there are two bobbles on the metal part of the bulb one is set higher than the other....so it does not fit the wrong way..to get the old one out you push down ,use a cloth just in case the bulb breaks..then twist anticlockwise..get your new bulb locate the bobbles correctly press and twist clockwise...test..and replace the cluster in its clip...dispose of the old bulb carefully...and pat yourself on the back as you just did it.
  • robin summer rentals
  • fish
  • How do brake tail lights change the color of the light you see?

    How do they change the light you see from white to red?
    How do brake tail lights change the color of the light you see?
    The white light that the lamp gives off contains all the colours of the spectrum:-



    Red, orange, yellow, green, blue, violet.



    You could say that of these colours, the red lens lets through the red light only (so we see red), and the other colours are absorbed by the red lens.( they don't get through the lens )



    In reality, the red lens also lets through a little of the other colours as well, but it lets through much more red than any other colour.
    How do brake tail lights change the color of the light you see?
    the lenses are colored.

    colored lenses only allow certain wavelengths of light through them.

    In the case a brake lights the red lenses only allow the red portion of the light bulbs light through.



    Hope this makes sense!
    The lens that the light passes through (the tail light lens) absorbs all light except red which passes unaffected. So all other colors are blocked except red.

    How do I change the middle brake light on my '06 Corolla?

    I know how to do access the side brake lights in the trunk, but how do you access the middle brake light that sits in the center of the back window?
    How do I change the middle brake light on my '06 Corolla?
    take it to your dealer
    How do I change the middle brake light on my '06 Corolla?
    I imagine it's through an access panel in the trunk.
    Pop the cover off by pulling at the corners away from the window, pull the tabs on the light shield, and replace the bulb with a 912 light bulb.